The Radio Subversion #2: Build Notes

 Let's Subvert This Radio !

First and foremost: make sure this radio kit  works completely out of the box before starting these modifications! These hacks are designed to rewrite a radio's architecture, not bring a dead project back to life. If you have an IC oriented backward or a cold solder joint, it is infinitely easier to track down and diagnose on a functioning, stock kit.

Notice the differences?   Oh yeah, you want one. 

Totally Subverted Radio (TSR01)


But First... The 90% Volume Rule

One critical thing you must verify before melting any solder is that your volume potentiometer has absolutely no skips or dropouts in its travel, especially at the upper 90% to 100% maximum volume level. The cheap potentiometers sourced in these budget kits have a notorious tendency for the internal wiper arms to lose physical contact with the thin carbon resistive element.

When we shift the FM section up into the VHF utility bands, we are going to need every single decibel of audio amplification this board can provide. This is because maritime traffic uses Narrowband FM (NBFM), while commercial broadcast stations use Wideband FM (WBFM). Squeezing an NBFM signal through a wideband discriminator means we lose a massive chunk of audio amplitude, and we must run the volume wide open to make up for it.

Furthermore, the VHF Air Band uses Amplitude Modulation (AM). We will be using AM Slope Demodulation to trick the FM chip into decoding aircraft voice traffic, and that hack demands an extreme audio boost. If you find a dead spot at the top of your volume wheel during stock testing, replace that control immediately!

(Fun note: My particular bench radio actually has a volume skip right in the 60%–70% range, but because it recovers cleanly in the 90%–100% bracket where we need it, I'm rolling with it!)

. 

The Subversion... Schematics! 

Here is the fully modified schematic layout. Yes, this shows the complete multi-band subversion, but don't panic—I have left a few step-by-step engineering hints below on exactly how to implement them.


CF210SP Schematic w/Mods


Phase 2: Let's Go Low. (The AM Side Sferics Mod)

You can actually complete this entire first phase with the main circuit board still mounted snugly inside its plastic casing.
Locate the two PCB pads labeled "AM". They should have the two thin copper wires running from the ferrite loopstick antenna coil soldered directly to them. Take your 150 pF (marked 151) ceramic disc capacitor and trim its leads down to about 1/4 inch so the component can lay perfectly flat near the pads. Solder the capacitor directly across the two AM pads. If needed, add a tiny drop of fresh solder, just make sure the original antenna coil wires remain securely attached to the pads!




150 pF Capacitor Installation 


That's it! Your receiver tank circuit is now permanently tuned down into our new Long Wave (LW) Sferics band. Pop the batteries back in and turn it on to verify. The daily AM broadcast talking heads should be completely gone, replaced entirely by the steady, rushing hiss of atmospheric noise, local buzzes, and electromagnetic hums. Move the radio near your computer monitor and the localized EMI will instantly swamp the audio!

⚠️ NOTE: You may still hear faint traces of local commercial music or broadcast images at certain points. This is completely normal; the FM side of the chip remains energized and a small amount of audio leaks into the power amplifier inputs even when the selector switch is toggled to the AM position.

Phase 2: Let's Gain Some Control  

The CD7642 AM chip is incredibly sensitive to supply voltage fluctuations. If we were to power it directly off raw battery voltage, its overall performance gain and Automatic Gain Control (AGC) tracking profile would constantly drift and degrade as the AA cells slowly drain.

To solve this, the designers exploited a beautiful law of physics: LEDs can act as primitive voltage regulators. Because a light-emitting diode requires a specific forward conduction current to ignite, it maintains a highly constant voltage drop across its junctions depending on its chemical color. 

The second current limits across the diode and it illuminates, the voltage across it locks down tightly between 1.8V and 2.0V, acting as a rock-solid shunt regulator until the batteries completely die.

We are going to exploit this chip's extreme voltage sensitivity by setting up a trimmer circuit to lock our operating gain right on the cliff, just below the LED circuit’s turn-on threshold.

Our small 10kΩ potentiometer has 3 pins that connect to the board using three 1-inch strands of thin 24 to 30 AWG insulated hookup wire.  Attach the three pins:

 1. V+ (Red Wire) + Vreg Attaches to the 2V we talked about. The spot is where C22 +lead and a triad of other components are soldered is a good spot.

 2. Gain (White Wire) The center pin (wiper) conects to IC1 pin 3. Connect to any component also attached to that supply.  The top of R8 or R10 are good points. 

3. GND (Black Wire).  Connect to any ground pad that is on the switched side. 

To comfortably reach our mounting point on the casing. You can solder these wires to the board points shown in the schematic now, but skip ahead for a second to see how the trimmer physically mounts to estimate how long they need to be. 

💡 TIP: If you solder raw wires straight to a small potentiometer’s pins, there is a very high probability they will snap clean off when you try to wrangle the wires through the tight radio case. To prevent this headache, simply fold the pot's pins flat against its plastic body or build it onto a tiny scrap of perfboard first to act as a strain relief.

Phase 3: Let There be (LED) Light

Now you know why our subverted instrument requires a second LED on the front panel. We need to assemble a custom add-on circuit to drive our visual strike indicators. In my opinion, this glowing indicator completely makes the modification!


 Improved LED Switch.  


At first glance, this looks like a typical bipolar junction transistor (BJT) saturated switch. While that’s technically true, we have integrated a critical modification that makes the LED infinitely more sensitive: we pre-bias the transistor. By using R4 to hold the base resting voltage right at ~0.62V to ~0.7V —the circuit requires a microscopic audio pulse to snap wide open.

Attach your custom flasher circuit to the radio layout using three wire taps:

   1. V+ (Red Wire): Solder directly to the main positive (+3V) rail where power enters the circuit board from the battery terminal.
   2. GND (Black Wire): Solder to any convenient ground trace pad (the ground sides of R6 or R7 are perfect targets).
   3. INPUT (Yellow Wire): Solder this directly to one of the raw audio output pins of the TDA2822 amplifier IC (Pin 1 or Pin 3). You can tap these cleanly at the pads for capacitors C26 or C27.

You will know you have successfully hooked into the correct pin if the front-panel LED starts flickering furiously when you hold the radio near an old CRT or computer monitor, and continues to flash identically even when you plug an earbud into the jack (silencing the main speaker).

 

Here are Pads & Wires 

To mount it, I simply wrapped a layer of electrical tape around the bottom of my custom flasher circuit to prevent it from shorting against anything, and tucked it neatly right under the main radio PCB. Here is a quick peak at a dedicated through-hole daughterboard PCB I am currently developing for this mod, and maybe even a SMT version.

PCB Concept - needs work! 


💡 TIP: Attach the LED  with a couple of thin insulated wires, use a small scrap of perf board to keep the LED leads flat and protect them from snapping off as shown.  

3mm LED Location

💡 TIP: You can see I used enamel covered wire.  It is well insulated so it can lay directly on a circuit board.   The catch is you need to scrape off the ends to solder to the pads and it is single conductor so it is prone to breaking at the joints. 

Phase 4: Case Modification Plan

This now completes the AM subversion.  Since we may need access to the component side for the VHF mods let's move forward and modify the case now. Start by removing the circuit board. We are probably going to need access to the component side now anyway and you really don't want to drill into the circuits . 

💡 TIP: Use a small donut magnet to save the tiny screws.  They stick like mad to it...maybe too much. But bonus they will be magnetic and help hold them to the screwdriver. 

The Drill Guide Plan

Measurements? You want precision measurements? Good luck! The factory went absolutely all-out on the retro aesthetics of this casing; there is hardly a straight geometric line anywhere on the chassis. Fortunately, you don't need a calipers or some magic bendy ruler tool—the factory molded a perfect, built-in grid array straight into the speaker grille. You just need to count the dimples. The speaker only occupies a small part of this grid: 

. 

Drill Guide


Drill out the holes using bits matched to the minimum diameters of the components you are using. The goal is to achieve a snug friction-fit so the parts don't  pop out of the case because most LEDs are a little wider rat the bottom and our selected resistor is rectangular and won't fit through if you are careful.  But if you do go too big... simply glue them in place! 

Here is how I mounted the sensitivity trimmer pot. You might look at this spot and think it's a terrible placement location because it sits right under the battery compartment, but look closer! 

LED ADJ Trim Pot Mounted

The pot fits beautifully inside the cavity and remains completely accessible and visible right through the small triangular cutout designed for the battery contact spring. There is plenty of clearance. Note that the component leads are folded completely flat against the body to allow hookup wires to attach securely surface mount pad style.


LED ADJ Pot With both shells

Test Setup 

If you want to test out your modifications before committing to the final assembly, you can set up a temporary flying-lead jumper array on your bench look exactly like this:


My Bench Setup

💡 TIP: An external 3V power supply is helpful.  Some testing or troubleshooting requires it.  Your test power can be as simple as a two AA battery holder and clip leads. 

Phase 5. Let's Go Up Now! (The VHF Marine Band Mod - Ships) 

It's time to tackle the high-frequency VHF transformation. By positioning your new components directly on the solder side (back side) of the PCB, you can fully reassemble the board into the front case shell and perform all your fine-tuning accessibly from the rear.

Pop the board out one last time to clear out the factory parts from the component side.

💡 TIP: Once you locate the target pads for the factory FM coils, use high-quality solder wick to clear the joints. The factory through-holes are significantly oversized; if you apply clean heat to both pads, you can simply pull the stock coils out from the component side with a tweezers while pushing from the back.

⚠️ CAUTION: Use the absolute minimum heat necessary and do not linger on the joints! The copper tracking on these ultra-budget phenolic boards is incredibly fragile, and it is remarkably easy to lift a pad clean off the fiberglass if you overheat it. 

 💡 TIP: I have often resorted to simply clipping the leads of parts save reworking  PCB.  Components are easily replaced but you only have one circuit board. 

Solder-Side Component Installation - Finally Subverted. 

Once the holes are clear, you can install your new custom-wound coils and squelch-defeat resistor. Bend the leads of your custom 4-turn and 6-turn 3mm ID coils outward "SMT-style" so they sit flat against the back solder pads for easy toothpick adjustment later. Lay the new 10kΩ pull-up resistor flat on its side so it clears the plastic rear case shell.


New Coils: L1 = 6T3, L2= 4T3


Secure the board back into the front radio housing using just two screws. We may need to get back inside for final scale tracking.  You can also remove the tuning scale and set it aside for now as well. It is infinitely easier to put the the plastic tuning pointer wheel without the dial scale and we will be changing that scale graphics shortly. 

The LED ADJ Setting 

With everything securely mounted, we can perform a quick calibration of our custom LED indicator loop:  The calibration is meant for Sferics, so the LED should be OFF on normal background noise and flash only on a wide-band static crash. 

   1. Turn the radio on, switch to the AM / LF  band, and tune to an empty frequency consisting of pure background noise. 

   2. Crank the volume wheel all the way up to its 100% maximum limit!

   3. Take a small adjustment screwdriver using the new adjustment on the front of the radio, and slowly rotate your LED ADJ Pot until the front-panel LED just transitions from a bright flicker to completely off. If the POWER LED starts to dim - you should back it off a bit to full brightness.  

⚠️ NOTE: As a bonus the LED also works on the FM band. 

Now Switch to FM/VHF and pull out the antenna - the LED should  glow or flicker furiously across open blocks of high-frequency white noise static. Tune slowly toward the very top of your vertical slide-rule track. 

The moment you tune near the station, the background static should start to drop into a dead quiet, the indicator LED will lock off, and (depending on how close you are to the NOAA broadcast transmitter) and the automated robotic voice should be broadcasting live local sea states and wind updates.

If you hear the NOAA robot voice playing cleanly at the top of your needle track, congratulations—your subverted utility monitor is officially calibrated and operational!  

⚠️ NOTE: If you don't get this signal at all or it is weak, don't panic yet - it may just need some dial calibration. Also, the clarity may  depend on how far you are from that signal. 

💡 TIP: You may want to ke screwdriver with you to re-adjust if needed. 

Next time, we will dive into printing, laminating, and aligning our custom dual-column slide-rule overlay to map out our inverted aircraft and ham channels. Until then...

...Stay Tuned!




Comments

Popular posts from this blog

The Radio Subversion #1: An Introduction to Ships & Sferics Modifications

A Radio Subversion #3 - Arts & Crafts, and Calibration

A Radio Subversion #4 - Sferics, Storms, and Low-Frequency Physics