A Radio Subversion #3 - Arts & Crafts, and Calibration
The LF/VHF Mirror Dial: Arts, Crafts, and Calibration
Welcome to the intersection of graphic design and RF alignment. Now that our circuit surgery is complete and our unmuted receiver is running wide open, we need to replace our old frequency reality. The stock plastic dial scale is now officially obsolete on your radio.
⚠️ NOTE: I used the exact original tick marks positions major and minor marks.
Today, we are going to use a blend of simple arts & crafts and precision bench adjustments to construct a beautiful LF and dual-column VHF Mirror Slide-Rule Dial just ike pictured above.
Although the scale is not very precise, it gives an idea on what transmissions you capture!
⚓️ TIP: There is not much need to calibrate the LF scale and these procedures won't affect that scale, but you can use a similar procedure if you have a known anchor in that range.
Step 1: Download & Verify the Template
![]() |
| Full Scale Template |
I have embedded two hard reference blocks directly into the graphic: a 1-inch square and a 10mm square. You may want to print a couple now that you have he scaling correct
- Right-click the image, open it in a new tab, and download the raw
.pngfile. - Drop it into your favorite software (Inkscape, CorelDRAW, or even a basic document editor) and adjust the print boundaries until a physical ruler placed on your desk matches the reference squares perfectly.
- Print it out on high-quality white copy paper or full-sheet matte sticker paper.
💡 TIP: Make sure your printer doesn't accidentally try to scale to fit and warp or shrink the dimensions, you want a 1:1 or 100% print. Use a ruler to test the dimensions on you print out!
Step 2: The Packing-Tape Lamination Method
To get a rugged, glossy, factory-grade protective finish without paying for a professional hot laminator , use this classic crafting trick, but you may still need a plastic credit card:
- Open the Window. Once printed out, Use a fresh, razor-sharp hobby knife and a steel ruler as a straightedge to carefully slice out the small strip of the window inner 3mm × 32mm window. (see tip below)
- Laminate. Take a strip of standard, clear 2-inch wide packing tape and stick it on the paper above the artwork using a plastic credit card or straight edge, keeping tension on the tape as you drag it smoothly at an angle over and beyond the printed artwork. Kind of like dragging a paint brush but in a single, fluid motion using only the edge. (take care not to get any fingerprints, dirt, or debris on the tape, especially in the center as it will have the adhesive exposed on that tiny window!)
- Finish. Take the edge of the plastic credit card and burnish the tape to the paper, driving out any trapped micro-bubbles to form a permanent laminate bond. (just like putting on a cell phone screen protector)
- Trim. Take a scissors or the hobby knife and steel ruler as a straightedge, to carefully cut out the outside 24mm × 56mm vertical sides. Leave the black border in place, cut as closely as possible. Just cut the 24mm sides first but go about 2-5mm beyond each side. Then carefully cut out both 56mm sides. Trim the outer borders with a small scissors to match the curved corners.
- Glue. Unless you used sticker paper apply your adhesive to the front of the original plastic faceplate. Remember, less is more - it really does not take much glue on this. Try not to get any glue on the window slot. Position the laminated scale to the front side over the original plastic plate, aligning the window slot perfectly over the physical needle track. Then press it firmly down onto the faceplate.
- Install. Attach the faceplate with the new slide scale to the radio front panel. The original sticky side should still stick it back on but it may need a little glue as well.
![]() |
| My tools - Arts & Crafts Time! |
💡 TIP: You can also punch out the Power LED hole in Step 1, but I recommend leaving the paper intact makes a nice diffuser for that light.
💡 TIP: It may take a couple tries to get the hang of this. You did print extra copies?
Step 3: Calibrating to an Anchor
⚓️⚓️⚓️
Because our new 4-turn local oscillator and 6-turn antenna coils are highly malleable, we will use a small adjustment screwdriver to finalize our dial scale calibration.
![]() |
| Adjustment Screw |
⚠️ NOTE: The screw is just to the left of our new 4-turn coil. I put a small Sharpie mark on the current position.
💡 TIP: Before tuning, see if you can find NOAA somewhere on the scale. If you do find it (it should be near the top of the dial) move the antenna to get the best signal. If it is parked on the center of the at 162.4 - you are done, no need to calibrate!
Fun Fact: My coil had it tuned at the very top of the dial. I moved it down to the 162.4 mark - which also moved the Aerobeacon noise on 118.0 off the bottom of the tuning range!
Setup:
You will need an external power supply. The back shell has the contacts for the batteries to connect (+) to (-) so without that no current can flow! Get a power supply set to 3.0 Volts or a small AA battery holder. Use alligator clips or temporally solder wires to connect the (+) to the positive input and the (-) to the negative side (the one with the spring).
Procedure:
- Power the radio on, Pull out the telescoping antenna, switch to the FM/VHF side, and crank the volume up until you hear the open static rush.
- Turn the main tuning wheel until the physical dial pointer sits exactly in the physical center of 162.4 MHz your new vertical slide track.
- Locate the small FM trimmer Adjustment screw on the back of the main variable capacitor casing. These are continuous 360-degree rotary trimmers, so don't worry about hitting a hard stop!
- Gently turn the trimmer screw with a non-magnetic screwdriver until the background noise drops out, your indicator LED locks off, and your local 162.4 MHz NOAA Weather Radio robot is clearly heard on the speaker.
By using the trimmer to park the high-power NOAA station precisely on its central mark, the rest of the folded spectrum automatically falls directly into line. As you tune down you are likely to hear hams on about the 146.0 mark, the marine channel 16 will materialize near the 156.8 mark; slide it down, and the airport control and aircraft chatter are around the 119.8 mark.
💡 TIP: If you don't have a NOAA Wx station nearby you can tune to basically any signals as long as you know what frequency they appear on. If may take longer to calibrate if they are not broadcast but intermittent.
Tune around and try finding Marine channel 16, since we know that is on 156.8 or even active 2M repeater, or an aircraft tower. Find the published frequency, put the slider on that frequency and adjust the capacitor until you hear it clearly. A scanner radio is also helpful to identify the channels.
💡 TIP: To find signals, slowly tune until you hear a drop in the background noise. Then home in until you hear the audio!
Congratulations!
Our custom radio is officially calibrated. Next time, I will explain some of the findings, features and physics behind some of the different Signals and Sferics you can now hear with this radio.
Until then...



Comments
Post a Comment