The Radio Subversion #1: An Introduction to Ships & Sferics Modifications

 

 If you can build this radio kit successfully you should also be able to modify it with no trouble! 

Before the radio subversion, I recommend to build the kit as intended and test it out. I do also recommend one change to place the supplied two FM coils on the Solder side of the board to allow easy changing and tuning. These are listed as 5mm coils but they are actually 3mm - which is good because they will fit under the back lid  and allow easy changing of coils.  Anyway, it is a fun kit to build and it usually works the first time.  




CF210SP Radio


The Ships & Sferics build transforms an innocent, entry-level CF210SP  soldering practice kit into a rugged, dual-band tactical tracking instrument. 
By actively overriding the factory constraints of the CD7642 AM chip and the CD9088 FM chip, we force the receiver architecture into two separate, undocumented operating modes.  

A Typical CF210SP Kit


After Subversion...

On the AM side the MW/LF band will be there ready to hear those natural lighting generated bursts , as well as sniffing out EMI and other LF noise around you.

On the FM side, you can expect to hear a chaotic mix of Weather, Ships, Airplanes, and Ham Radio Operators cascading across the dial. Let's break down the core hardware changes first, and then we will dive into what you need to do to subvert your own radio!
Despite completely changing the radio's entire scientific identity, the component count is remarkably low—requiring just 4 primary core component changes: 
  • The 151 (150 pF) Disc Cap: Added across the AM ferrite tank circuit to drop the radio floor into the 350–475 kHz lightning/LF band.
  • The 10kΩ Pull-Up Resistor: Swapped in place of the factory 33kΩ resistor on Pin 1 to permanently defeat the internal squelch and mute loop.
  • The 4-Turn 3mm ID Coil: Dropped into the local oscillator slot (L2) to shift the tuning window up into the 156–162 MHz spectrum.
  • The 6-Turn 3mm ID Coil: Swapped into the front-end antenna circuit (L1) to serve as a custom high-gain bandpass filter.
Two other simple additions—a small 10kΩ potentiometer for threshold trimming, and a custom LED/transistor switch circuit—really make this modification different by adding a sharp visual indication of incoming signals.


The AM Side Subversion (Sferics & Signal Sniffing)

To be perfectly honest, I really did not have a need for a standard consumer AM radio. A bunch of talking heads, sports broadcasts, and religious programming dominate the commercial band, with just a light sprinkling of news traffic and weather. The only real fun thing left to do on a stock AM dial is listen to open channel frequencies at night to catch long-distance skywave skips!

"Sferics" are natural radio signals generated by lightning discharges. You can technically hear them on a standard AM radio, but they are usually buried in between all the non-natural commercial signals mentioned above. The goal of this first modification was to move the receiver's range entirely below the normal 550–1600 kHz broadcast band to find a quiet window for clean tracking.

Theory of Operation

The AM heart of this kit consists of a remarkable 3-pin integrated circuit: the CD7642 AM chip. Looking at its internal architecture, it is essentially a high-gain array of transistors that forms the complete RF amplifier and detector stage for a simple Tuned Radio Frequency (TRF) radio complete with Automatic Gain Control (AGC).  This simple three-pin chip makes the basis for a highly sensitive AM receiver. 
Equivalent CD7642 Circuit

The modification of the radio is simple: add a 150 pF disc capacitor (marked 151) in parallel with the existing ferrite bar antenna coil and the main mechanical tuning capacitor. After some trial and error, I found this value to be absolutely ideal. It drops the tuning range down to a clean 350–475 kHz floor.

How Low Can You Go?

Because this is a pure amplitude modulation (AM) detector, we are probably not going to hear the legendary VLF "whistlers" or spooky magnetospheric sounds even if we could tune this circuit all the way down to the audio range below 20 kHz. There is nothing for the detector to detect...it's already audio! Besides physical loopstick coil that comes with this kit is simply too small to gather the massive magnetic flux lines of a VLF wave.
Furthermore, the standard Manganese-Zinc (MnZn) ferrite core used in these AM band antennas acts as a natural filter that drops in efficiency as frequencies fall. 
However, even though you can calculate a lower frequency ranges with this inductor - you just can't simply slap on a larger capacitors because the signals on the stock AM coil really start to drop off aggressively below 300 kHz, meaning even a slightly larger 200 pF capacitor resulted in a noticeable drop-off in signal reception performance.
To test these physical boundaries, I actually attempted to swap in a high-permeability coil harvested from an old Atomic Clock to see if I could anchor down near the 65 kHz time-signal range. However, the coil presented a terrible impedance mismatch to the tiny TRF chip, and no signals could pass through.
I could have overcome this by adding a secondary winding or even a FET pre-amplifier stage, perhaps harvesting a low-voltage 3V FET out of a common electret microphone capsule! 

Calibration Strategy

I wanted a clear indication of exactly what frequencies I was tuning into. The solution was designing a custom stick-on layout label to place directly over the kit's existing slide-rule dial window.
This new low-frequency range is almost ideal because there are virtually no commercial broadcasts or heavy local signals down here to clutter the spectrum. But that is exactly what you want for a dedicated sferics monitor! 
To calibrate the dial marks, I hooked the receiver up to a GW Instek AFG-125 Arbitrary Function Generator—set up with 1kHz AM modulation to map out the exact frequency coordinate bounds. If you don't have an RF generator, don't worry—the printable template I will provide in the next Posts should line up close enough for your subversive radio!

The FM Side Subversion: Theory of Operation

Because this budget chip uses a tiny 70 kHz internal filter, it lacks the ability to reject 'image' frequencies. When we speed up the internal oscillator to track the Marine band, the chip's internal mixing transistors act as high-speed switches. This effectively folds the radio spectrum over like a mirror, mapping high-altitude airplanes and local ham operators right alongside our maritime channels on the exact same dial tracks. 
When we substitute a custom 4-turn/6-turn air coils on the board, this new inductor combination inadvertently caused a low-side/high-side injection flip. 
This architectural change forces the physical dial track to expand non-linearly, effectively folding the spectrum over on itself. When the variable capacitor opens up and your oscillator climbs toward your 162.4 MHz NOAA Weather Anchor, the real-world frequencies it intercepts from lower in the bands also populate by the same tuning setting! 
CD9088 Chip Block Diagram

⚠️ Note: The NOAA Weather Radio band actully consists of seven VHF-FM frequencies ranging from 162.400 MHz to 162.550 MHz. These channels, often labeled WX1 through WX7. 

The Math Behind The Mirror Spectrum

The CD9088 / TDA7088 receiver architecture operates on a strict low-side/high-side heterodyne mixing math rule. In the factory configuration, the internal Local Oscillator (LO) tracks exactly 70 kHz away from the incoming station to hit the chip's internal Intermediate Frequency (IF).  To explore the internal Frequency-Locked Loop (FLL) and mixing configurations the technical architecture of the Philips TDA7088 / CD9088 FM Chip. 

Harmonic Generation is the driver of the he "Ghost" Mixers. Because the mixer is effectively slicing the RF signal like a square wave, it introduces the mathematical reality of a square wave: heavy odd-order harmonics 3xLO, 5xLO...etc

The  Predicted VHF Mirror Table

Here is how I made the slide rule tuning dial that uses only  a few Cardinal Frequencies side-by-side to make the vertical slide rule hopefully it is intuitive to read and help you identify what you hear:

    =================================
           VHF  MIRROR LOG
    =================================
       TRUE BAND   |   MIRROR BAND
      (Ships/NOAA) |   (Air/Ham)
                   |
     NOAA [162.4]  |    
| [146.0] HAM MAR [159.0] |
|
[132.6] MIL CH16 [156.8] | | [119.8] AIR | UTIL [150.0] | | [118.0] AIR
=================================
You should never hear two channels at once—thanks to the FM capture effect. The strongest signal will win.  To find a transmitter simply rock the tuning knob back and fourth around the mark and when the signal starts to lock is indicated on the LED (I will explain that later)  allowing tuning right to the signal. 

NOTE:  I will post the how to make the LED Circuit and how to adjust it. 
 

Calibrating the Tuning 

Again, I mapped out these cardinal points for you with a tinySA that generated FM modulated signals in these bands—so lining up one known broadcast station will line up the rest of the dial. 
The 162.4 NOAA mark serves as the physical "tuning anchor." If you calibrate with a 4-turn 3mm coil so that the local robotic weather voice sits right at the top left mark, the radio's architecture will automatically fall into place, lining up the airport traffic on the bottom right and the boats in the center! 
There is an adjustment screw on the main tuning capacitor, I will show you how to tune it precisely later to let you line up the dial. The alternative tuning method  of separating the windings—which will only reduce the inductance of the coil—is not needed. 


The Subverted Tuning Scale

With both bands the new tuning scale looks like this:  
New Tuning Slide


NOTE:  I will post the 1:1 artwork for the dial and how to make it simple to modify your on dial tuning scale. 
 

The Power Audio Amplifier Chip 

Finally the audio amp use drives the speaker incredibly well as a bridge configured power amplifier. The only subversion on this part is where to get the audio to drive the LED.  TDA2822  I was actually impressed by this chip - it is now obsolete but it actually produces some decent volume with a low-voltage battery supply. There is no ground connected to the speaker the chip drives it in a push-pull configuration which eliminates the audio output transformer typically used in low voltage transistor radios to squeeze more audio drive with limited battery power. 

TDA2822 Bridge Circuit




The "Ships & Sferics" Radio Subversion Plan 

These post are being documented post-implementation, I will provide more detailed instructions and documentation in later posts!

Step 1: The LF / VLF Atmospheric Tracker (AM Section)

The stock AM section uses a CD7642 Tuned Radio Frequency (TRF) receiver IC paired with a ferrite loopstick (bar) antenna, natively restricted to the standard AM broadcast band (530–1600 kHz).  The idea is to put the reception range below any broadcast band stations that will interfere with detection. 

Shifting the Frequency Floor

To plunge the radio down into the Low Frequency (LF) spectrum (350–475 kHz), a 151 (150 pF) disc capacitor is soldered directly in parallel across the tuning tank circuit.
  • This extra capacitance acts as an electrical brake, slowing down the resonant frequency of the LC loop.
  • The resulting 358 to 475 kHz window completely strips away standard commercial broadcasts. Instead, it optimizes the high-gain ferrite rod to capture groundwaves and low-angle skywaves bouncing through the atmospheric waveguide.

Observed Phenomena: Sferics & Electronic Sniffing

  • Long-Distance Lightning (Sferics): High-voltage electrostatic discharges from storms hundreds of miles away release broad-spectrum RF pulses. The modified front-end catches these pulses instantly, registering them as sharp audio crackles.
  • Qi Wireless Charger RDF (Radio Direction Finding):  During testing I found that a Standard smartphone wireless charging docks emit a low-power, modulated electromagnetic "ping" between 375 and 400 kHz to check for a phone. The subverted radio picked this up as a rhythmic, metronome-like ticking sound, turning the radio into a highly directional hidden-electronics sniffer.
  • FM Bleed Through.  If you decide to keep those automated commercial FM stations along with just the Sferics  modification be aware, the FM section is always powered on.  With the now mostly silent AM side you can hear some of the the loud FM stations bleeding through as you tune, because the audio is simply switched between the two sections. 

Step 2: The VHF Utility & Mirror Monitor (FM Section)

The FM section relies on the CD9088, a low-cost Frequency-Locked Loop (FLL) receiver chip with a tiny 70 kHz Intermediate Frequency (IF), natively configured for Wideband FM (88–108 MHz).

The Dual Coil-ectomy (Inductance Shifting) 

To leap from those automated consumer FM music stations up into the high-altitude VHF Air Band (108–137 MHz)  and even the maritime VHF Marine Band (156–162 MHz) , the factory coils must undergo a severe reduction in inductance:
  • The Oscillator Coil (L2): Replaced with a custom 4-turn, 3mm inner diameter (ID) air-core coil. This pushes the tuning window ceiling up to align a local 162.4 MHz NOAA Weather Radio beacon perfectly at the top edge of the dial track.
  • The RF Input / Antenna Filter Coil (L1): Replaced with a 6-turn, 3mm ID coil soldered directly onto the back of the circuit board. This tightens the front-end bandpass window, blocking heavy commercial FM bleed-through and maximizing signal gain.  
  • Fabricaing the Coils.   A Philips PH0 size Screwdriver makes a perfect mandrill to wind the coils on.  Any rod or dowel slightly smaller than 3mm to allow for some spring back should work. 
The New 3mm Coils. 

Well I guess these are technically transplants because the original coils are replaced by new ones! 

💡 TIP: If you don't want to wind your own coils as you can easily the original coils.  Remove the coils and place on a 3mm mandrill.  Unwind until only the number turns remains and cut off the excess to match the original lead. You will need to scrape and tin the lead with some solder. 

Defeating the Squelch and Audio Blanking

The factory configuration keeps the audio output path completely muted unless a massive commercial signal is present.  With this enabled the tuning will stick to the loudest signal and only snap away like a rubber band to the next  only when you tune far enough away from the original signal.  There is little interstation noise but to pull weak, marginal utility signals out of the background mud:
  • The 33kΩ factory mute resistor on Pin 1 is excised.
  • A 10kΩ pull-up resistor is bridged from Pin 1 directly to VCC (+3V).
  • This permanently overrides the audio clamping circuit, keeping the receiver wide open and generating a continuous, high-gain FM background static hiss.

The Inverted Mirror Dial Effect

Because the front-end filter is wide and the chip operates with a microscopic 70 kHz IF, the radio undergoes Local Oscillator (LO) Image Inversion. The radio folds the VHF spectrum in half like a mirror.
  • As the tuning wheel moves upward toward the 162.4 MHz NOAA anchor, lower-frequency signals show up in reverse order.
  • This allows the radio to cleanly process 2-Meter Ham Repeaters (~146 MHz) just below the NOAA Weather channel on the Mirror Band tuning scale. 
  • I hear a local airport's tower is communicating with general aviation traffic practicing touch-and-goes (119.875 MHz AM via Slope Detection) on the exact same mechanical dial sweep almost opposite of the marine band channel 16 on 156.8 MHz.

Step 3: The Multi-Purpose Transistor & LED Feedback Stage

A custom transistor amplifier switch is tapped directly into Pins 1 and 3 of the TDA2822 audio amplifier. This hardware placement bypasses the headphone jack, keeping the tracking loops alive even when earbuds are plugged in.
LED Switch Prototype

Note that the transistor and capacitor are laying flat.  This is because the case does not have much vertical space to be able to screw the case shells back together.  I may provide a PCB layout (through hole or SMT) to make this more repeatable, at least a little easier to build.  

An internal bias potentiometer is glued inside the case to let you adjust it with a small screwdriver establish a manual triggering threshold:
 Trimpot WH06-2C Adjustable Resistor, 

This little pot can be found by multiple suppliers. There is a subtle feature of this part that makes it ideal for this subversion. Notice the body of the potentiometer is larger that the yellow movable knob -  this means if you drill a hole to pass just the knob, the base keeps it inside the case...a dab of glue is all you will need to attach it to the case. 
The LED is used in two different modes: 
  • In Sferics Mode: The lightning sferics  (also high-frequency AC, voltage spikes, or any loud audio signal) will  punch through the bias threshold, causing the custom front-panel LED to flash brightly in real-time. This is really why we need the adjustment because you set the LED to just turning off with normal volume and not flicker with only the background noise. 
  • In VHF Tuning Mode (The Signal (un)Lock Indicator): In open spectrum the loud, continuous FM background hiss keeps the LED flickering furiously. The moment the internal FLL "snaps" onto a clean carrier wave, the background noise floor instantly drops. The voltage falls below the bias threshold, causing the LED to go completely dark—providing a visual indicator that a station is successfully locked.

Step 4: Modify the Case

Fitting the extra parts in, particularly the LED and potentiometer requires drilling a couple of holes (one for the LED and one for the trimmer) and attaching them onto the case. This also required a little planning - there is not much room for extra parts! But I found some spaces to make it all fit!  Also, I will show how to make and attach the custom slide rule tuning dial to make the build complete. 

To pull this subversion off, you won't need a massive laboratory budget or hard-to-source silicon. The component count for this dual-band overhaul is incredibly low, and you can put it together using basic tools sitting on your workbench right now.
In my next post, I will present the complete, step-by-step construction notes, component callouts, and layout diagrams you need to perform this exact circuit surgery on your own kit.
Oh, and if you do complete these mods please let me know in the comments! 
 Until then...

...Stay Tuned!


Comments

Popular posts from this blog

A Radio Subversion #3 - Arts & Crafts, and Calibration

A Radio Subversion #4 - Sferics, Storms, and Low-Frequency Physics